How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
Are you hunting for advice around Installing A Bathtub?
Mounting a bath tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the job can relocate quickly; if you have to open up a wall surface to remove the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually qualified on your own for the work and are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to think about using one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This article will assist you install a new tub in your shower room if you have currently gotten a brand-new bathtub and also do not require to change the arrangement of your previous water supply pipes.
Your devices as well as material checklist should consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the needed position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the bathtub must wait till the bath tub has been utilized a minimum of once as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location between the tap and the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall between the bath and also the tiling, causing problems with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water before securing, to permit the motion experienced when the tub remains in use. The sealer can break rather very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that report about Tools You Need to Install a New Bathtub through a good friend on another site. Sharing is nice. Who knows, you may very well be helping someone out. Thanks a lot for taking the time to read it.
Appointment Report this page